-
DIY Finasteride and Dutasteride Spray - DMSO and PG and Water
Hi Guys
So I've created my own DIY mix, can you let me know what you think about ratios
To provide 60ML sprayable solution from old Regaine bottle ( Regaine removed )
DMSO 10%
Monopropylene Glycol ( PG ) 20%
Distilled Water 70%
Dutasteride 0.1%
Finasteride 0.1%
Interestingly I've never been able to dissolve Dutasteride powder before it always stayed as small particles but the DMSO does a great job of this so for the first time it's dissolved a 100% into a DIY mix, the PG adds a really nice topical solution that sits on the skin for a good 10 mins before slowly evaporating or being absorbed into the skin probably because of the DMSO.
Anyway let me know what you think, i'm amazed by the properties of DMSO and it's ability to transfer almost anything through the skin and was originally planning on using 100% DMSO until I tried it and holy moly that stung, so I have reduced this to a much safer ratio of 10% which seems to be much kinder to my skin and when reading a few scientific papers didn't harm cells at this concentration.
Anyway not sure if anyone still comments on this forum, I've posted messages before and not seen a single reply whee discussing this sort of topic.
Seems a shame as a DIY mix is so much cheaper and apart from the Dut and Fin is all available on Amazon
-
Buy from here they sell Topical Finesteride and Dutasteride.
https://www.baldtruthtalk.com/thread...%21?highlight=
-
Originally Posted by HairGuru
Thanks but why would I pay when I can make it for a fraction of the cost ? The DMSO is a pretty incredible substance if you read up about it ( also it can dissolve the dutasteride ) and allow it to absorbed into the skin better then almost any other substance in existence.
-
Anyone check my ratios ?
Originally Posted by lucky13
Hi Guys
So I've created my own DIY mix, can you let me know what you think about ratios
To provide 60ML sprayable solution from old Regaine bottle ( Regaine removed )
DMSO 10%
Monopropylene Glycol ( PG ) 20%
Distilled Water 70%
Dutasteride 0.1%
Finasteride 0.1%
Interestingly I've never been able to dissolve Dutasteride powder before it always stayed as small particles but the DMSO does a great job of this so for the first time it's dissolved a 100% into a DIY mix, the PG adds a really nice topical solution that sits on the skin for a good 10 mins before slowly evaporating or being absorbed into the skin probably because of the DMSO.
Anyway let me know what you think, i'm amazed by the properties of DMSO and it's ability to transfer almost anything through the skin and was originally planning on using 100% DMSO until I tried it and holy moly that stung, so I have reduced this to a much safer ratio of 10% which seems to be much kinder to my skin and when reading a few scientific papers didn't harm cells at this concentration.
Anyway not sure if anyone still comments on this forum, I've posted messages before and not seen a single reply whee discussing this sort of topic.
Seems a shame as a DIY mix is so much cheaper and apart from the Dut and Fin is all available on Amazon
How do my ratios look above ?
-
wow is this site totally dead now ?
-
-
I would not actually experiment with homemade remedies because it is very easy to get it wrong in dosage, concentration, etc.
Similar Threads
-
By mriordan23 in forum Men's Hair Loss: Start Your Own Topic
Replies: 3
Last Post: 05-31-2020, 08:19 AM
-
By AbuHanifa786 in forum Hair Loss Treatments
Replies: 12
Last Post: 07-06-2016, 09:09 AM
-
By champpy in forum Cutting Edge / Future Treatments
Replies: 12
Last Post: 01-23-2016, 05:33 AM
-
By Daytona in forum Hair Loss Treatments
Replies: 9
Last Post: 07-18-2013, 04:35 PM
-
By chewytorch in forum Men's Hair Loss: Start Your Own Topic
Replies: 5
Last Post: 02-13-2013, 04:52 PM
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
Forum Rules
|
» IAHRS
» The Bald Truth
» americanhairloss.org
|
Bookmarks